High-Performance Vinyl Ester Resin Tooling Gel Coat, Good Gloss Rentation, High Hdt

• Customization: Available
• Molecular Principal Chain: Carbon Chain Polymer
• Color: Orange or Black
• Model NO.: Vinyl ester resin base tooling Gel coat
• Thixotropic Index(6/60rpm): 5.0-7.0
• Flash Point: 31°c
• Solid Content: 40-50%
• Gel Time(Mins): 10-30
• Specification: 20kg with PE liner
• Trademark: Promisechem
• Origin: Changzhou China
• Package Size: 1000.00cm * 1000.00cm * 1000.00cm
• Package Gross Weight: 1000.000kg

Product Description

Vinyl ester tooling Gel coat

Product Description

Description

Vinyl ester resin base tooling gel coat is formulated
specifically for composites mold application.
It can be exhibits high heat distortion to withstand the repeated molding of FRP laminates. These products do not contain lead. They are formulated to provide abrasion resistance, good gloss retention, High HDT and extended mold life.  

Package
20kg with PE liner.

Shelf life
- 3months under 25ºC,away from  heat sources, direct sunlight or steam pipes,rain etc.
- Keep sealed to prevent moisture pick-up and monomer loss.

Application attention:
- Generally best results are obtained by applying two coats at 18mils wet each, and allowing the gel coat to gel and cure between coats. Apply each coat with a minimum of two passes; three passes are preferred. For best results, ensure that the tooling gel coat is allowed to "breathe" for two minutes between each pass. Do not allow over-spray and thin passes to go beyond 5 minutes without covering with a fresh pass.

- Recommended Gel time be checked in the customer's plant because age, temperature, humidity and catalyst will produce varied gel times.

- Do not use more than 3.0% catalyst in the tooling gel coat, as this can cause excessive shrinkage of the gel coat and pull it away from the plug. For adequate cure, do not use less than 1.2% catalyst.

- Normally, tooling gel coats are ready to lay-up on (or spray with a second coat of gel coat) in 60 - 90 minutes.

- Using conventional tooling resin, the gel coat should not be left overnight before being laminated  as the gel coat may pre-release or lose its stick

- UV and moisture resistance will be limited due to vinyl ester resin . Recommended that molds  should be stored outside away from UV and moisture exposure. This may be accomplished by covering the mold or inverting the mold so that the surface is not exposed to UV and that moisture cannot collect on the mold.

- Tooling gel coats may leave a certain amount of "color" when sanded and/or buffed. This is a function of the pigment used and is not an indication of cure.

- Do not add anything, other than the appropriate methyl ethyl ketone peroxide, to these products.
 

Product Parameters

Liquid properties at 25ºC:
Below listed for a reference guide only. Batches will not conform exactly to the numbers listed due to storage condition, temperature , age, testing equipment can  have a significant effect on the test results. Gel coats with properties outside of these ranges can perform acceptably.

Item	value
color	Orange or black
Viscosity (brookfield RVT #4@60rpm	2000-3000 mPa.s
Thixotropic index(6/60rpm)	5.0-7.0
Flash point	31ºC
Solid content	40-50%
Gel time(mins)	10-30

Total tooling resins solutions for composites mold

We could offers a full line of tooling resins for all methods of tooling manufacture. These products include epoxy ,unsaturated polyester, vinyl ester and a series of low profile resins.

- Tooling gel coats are formulated specifically for mold making. These series contain both special polyester and vinyl ester products.

- Skin coat.Superior mold cosmetics can be achieved by using a skin coat with hybrid vinyl ester resin behind the gel coat. Be applied after the gel coat application and offer good protection from fiber-print and distortion on the gel coat surface in order to increase mould turnaround time.

- A full line of tooling resins for all methods of tool manufacture. These products include a vinyl ester and a series of low profile resins. The vinyl ester resin can be used as skin and bulk materials in the conventional mold building process. This process consists of daily single ply lamination until the required mold skin thickness is achieved.

Application	Procedure	Product type	Description
Master mold(Plug) construction	Frame construction	Epoxy	Atmospheric temperature
		Polyester	styrene free version
	Tooling paste	Epoxy	Low density, hand up/extrude
		Unsaturated polyester	Low styrene, spray/extrude
		Vinyl ester	High HDT, Low styrene,  spray & extrude
	Surface finish	Sanding Gelcoat	Easy sanding, good gloss
		High gloss Gelcoat	High gloss
Female mold construction	Tooling Gel coat	ISO	High HDT, Good gloss
		Vinyl ester resin	High gloss recovery
		Vinyl ester resin	High HDT/gloss retention
	Skin coat	Vinyl ester resin	Low shrinkage
		Vinyl ester resin modified	Low shrinkage, thin lamination
	Traditional bulk resin	ISO unsaturated polyester resin	HDT:130ºC
		Vinyl ester resin	High elongation
		Vinyl ester resin modified	Low shrinkage
	Low profile controlled resin	filled	Low shrinkage/profiled
		Un-filled	Low shrinkage/profiled, High HDT.

Packaging & Shipping

 

Company Profile

We focus on composites resin business and have a tolling plant in Changzhou city. We can supply all kinds of modified resin to feed up your solutions for composites. The business covers the total composites industry.

Laboratory

FAQ

Q1:Do you provide sample for the trial?
A1:We could supply small size package for free.but we have to charge the freight.

Q2.Could you supply customized products friendly?
A2: Yes,we do.We have a team to sever in Fortune 500 and be able to supply products to satisfied with the end-users' technical requirement.

Q3. What about your lead time? 
A3: Generally 2-4weeks after the order confirmed.

Q4. What are your terms of payment?
A4:Usually we do EXW, FOB, CIF, and DDP.